Most custom jewelry case projects begin with one sentence: "I need a 1.2-meter case." What almost nobody states is who that height is for, whether staff will have to lean for every tray, and whether a customer in a wheelchair can see anything inside. Display case dimensions are not really a cabinet question — they are a human question. The four sections below cover the whole problem, in the order that actually works: measure people first, then measure the case.
Figures are common industry reference values compiled from published ergonomic sources and typical custom-fixture practice. Confirm them against on-site measurements and your supplier before ordering.
Measure People First: The Body Sets the Dimensions, Not the Sample
Published adult anthropometric data for the Chinese market puts standing eye height at roughly 145–155 cm for women and 155–165 cm for men. Comfortable jewelry viewing happens with the eyes angled about 15°–30° below horizontal, which places the visual center of a countertop piece 15–25 cm below eye height — the 120–140 cm band. That is precisely why jewelry counter height, measured to the finished glass top, so often lands at 90–100 cm: the counter plus a 10–20 cm riser inside puts the product straight into the comfortable downward sightline. A taller case at 100–105 cm is workable for a taller clientele, but calculate it from your own customers' eye heights rather than copying another store.
Comfortable forward reach while standing is about 40–55 cm, and anything deeper than 50 cm forces a visible lean — a figure that simultaneously caps counter depth and staff-side shelf depth. A seated wheelchair user's eye height typically sits around 110–120 cm, so the primary collection should occupy a display band of roughly 80–130 cm where both standing and seated customers are covered; the zone below 80 cm and above 160 cm on a tall unit is no place for product that needs close inspection.
Children matter just as much: at 6–12 years old, eye height runs about 100–125 cm, so one or two low display positions along the main aisle, with product centers at 100–110 cm, change who the store can actually reach. The simplest self-check is to crouch to 110 cm and scan the room, noticing which cases simply vanish from a child's view.
Standing-view counters — islands and low wall runs — finish at 90–100 cm including glass, with 95 cm the most common figure; 8–15 cm of clearance between the underside of the glass and the display surface is enough, since more looks empty and less will not take a standing necklace display. Seated try-on and consultation counters follow entirely different logic: the customer is sitting and both parties talk across the top at eye level, so 75–80 cm is the usual range, chosen so forearms rest naturally on the surface.
Avoid fixed cross rails below, and reserve top space for a try-on pad, loupe and cloth, which pushes depth requirements higher than a standing-view counter. Tall wall cabinets run 180–220 cm overall, but only the 80–160 cm band is real display space; above that belongs to light boxes, brand imagery or stock.
Single-sided viewing counters are typically 45–55 cm deep; double-sided units combining a customer face with staff storage usually total 55–75 cm. Past about 60 cm, staff lean to reach the innermost tray. The verification is direct: drop the primary tray into the drawing and leave 2–3 cm between the tray edge and the inner glass. If the back row sits more than 50 cm from the rear of the counter, add pull-out shelves or reduce depth. Inside, 12–18 cm of clear height handles single-tray ring and earring presentation, standing necklace displays need their prop height plus 3–5 cm, and every 15–20 cm drop between levels compresses the viewing angle below it — fewer levels almost always beat more.
Lock the tray and price card formats before you order
Common full-size trays sit around 44–46 cm by 30–33 cm, with half trays at roughly half that. The correct sequence is to choose the tray system first and then design compartments backwards from the tray's real external dimensions, leaving 0.5–1 cm clearance per compartment; standardize on one format per store, because mixing two turns insert design and restocking into guesswork. Price cards commonly run 3–5 cm wide and 5–7 cm tall so the item name and weight stay legible at 40 cm. Electronic shelf labels need their own allowance — they are thicker than paper, so slots must widen. Keep 15–25 cm between the LED strip or spotlight and the top of the product to avoid both heat build-up and glare.
Whichever mechanism the rear access uses — lift-up, sliding or double door — the clear opening should be at least 60 cm so a tray with a 55 cm diagonal can be lifted in and out flat. Hinged doors need their swing and hinge-side footprint accounted for, and an open door must not block the adjacent compartment; lift-up doors need their raised clearance checked against the ceiling and light cove. Behind the counter, leave 80–90 cm to the wall or the next run for a single staff member, and 120 cm or more where two people work at once or a trolley passes. A 55 cm drawer fully extended still needs someone standing in front of it, and that strip of floor is the single most frequently omitted dimension on a drawing.
The main aisle—the route connecting entrance and cash wrap—should be at least 120 cm clear so two customers pass comfortably, with secondary aisles between cases at 90 cm or more. A wheelchair needs roughly 91.5 cm of clear width, following the ADA 36-inch reference, and about 150 cm to turn in place, so at least one spot at a counter end or in the try-on area must allow that turn. Keep a 1.5 m buffer between the entrance and the first run of cases so incoming and browsing traffic do not collide. To self-check, map every point where a person stops — browsing, trying on, queuing, restocking — and wherever two paths cross, adopt the larger of the two required widths.
The most common mistake is setting counter height by appearance rather than deriving it from eye height. The second is drawing only the customer face and forgetting staff access, which one walk-through of the tray-pulling motion would expose.
The third is measuring aisles on the plan instead of at the places people actually stop, so try-on positions and queue zones never enter the numbers. The fourth is finalizing trays after the case is ordered, when the sequence should always run from tray system to compartment grid. The fifth is leaving nothing for seated customers and children, when one low display position each costs very little and measurably widens the audience a store serves.
Lighting, liners and props can all be revised. The height, depth and circulation of a case, once built, are effectively permanent. Work through the four groups above before the drawing is signed off, and most dimensional rework disappears at the design stage. If you are planning custom jewelry display cases, contact us for a one-to-one dimension review and drawing assessment based on your floor plan, customer profile and product mix.
A: Not always. It is a popular size, but you need to adjust it for your customers’ height and the risers inside.
A: Trays are used every day for restocking. Inserts built around trays make picking easy. If you do it the other way around, trays often get stuck.
A: It holds more items on paper, yet staff struggle to reach the back. Deep counters need pull‑out shelves to avoid knocks.
A: Floor plans ignore occupied space from try‑on, queues and restocking. Keep main aisles at 1.2 m minimum with room for wheelchair turning.
A: They also let kids see the pieces clearly. A couple of lower display spots bring a much friendlier shopping experience.
Project